|
Who's Online
There currently are 5996 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
This manual was very good & was very helpful with repairs.
Always great & fast service from Owner's manual.
;
Very pleased with the quality of the scan. No complaints whatsoever.
;
I liked the product. I would use their sevices again.
;
I Recently purchased yet another Service Manual from Owner-Manuals.com, this time for a Sony EVS700ES/UB Videocassette Recorder. The Manual was available for upload within two hours and is an Extremely Good copy, as some of this I was able to enlarge to get even better detail.
Once Again, Very happy with the result!
;
A good and useful manual. With these, We was abled to isolate and pin point the component that was causing the problem. The total time spent in troubleshooting is very much reduced.
ELECTRICAL ADJUSTMENTS
2-8: BRIGHT CENT 1. Receive the monoscope pattern. (RF Input) 2. Set the screen mode to FULL. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (43) on the remote control to select "BRI CENT". 5. Press the VOL. UP/DOWN button on the remote control until the white 2.7% is starting to be visible 6. Receive the monoscope pattern. (Audio Video Input) 7. Press the TV/VIDEO button on the remote control to set to the AV mode. Then perform the above adjustments 2~5. 8. Receive the monoscope pattern. 9. Press the TV/VIDEO button on the remote control to set to the CS mode.Then perform the above adjustments 2~5. 10. Receive the monoscope pattern. 11. Press the TV/VIDEO button on the remote control to set to the HD-MI mode.Then perform the above adjustments 2~5. 2-9: SUB CONTRAST 1. Set the screen mode to FULL. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (52) on the remote control to select "SUB CONT". 3. Check if the step No. SUB CONT is "14". 4. Receive a broadcast and check if the picture is normal. 5. Press the TV/VIDEO button on the remote control to set to the AV mode. 6. Activate the adjustment mode display of Fig. 1-1 and press the channel button (52) on the remote control to select "SUB CONT". 7. Check if the step No. SUB CONT is "16". 8. Receive a broadcast and check if the picture is normal. 9. Press the TV/VIDEO button on the remote control to set to the CS mode. 10. Activate the adjustment mode display of Fig. 1-1 and press the channel button (52) on the remote control to select "SUB CONT". 11. Check if the step No. SUB CONT is "21". 12. Receive a broadcast and check if the picture is normal. Press the TV/VIDEO button on the remote control to set to the HD-MI mode. 13. Activate the adjustment mode display of Fig. 1-1 and press the channel button (52) on the remote control to select "SUB CONT". 14. Check if the step No. SUB CONT is "22". 15. Receive a broadcast and check if the picture is normal. 2-10: TRAPEZIUM 1. Receive the crosshatch signal from the Pattern Generator. 2. Press the MENU button. And, then press the LEFT/ RIGHT button on the remote control until the PICTURE menu appears. 3. Press the LEFT/RIGHT button on the remote control to highlight DISPLAY FORMAT. 4. Press the LEFT/RIGHT button on the remote control to select 1080i. 5. Set the screen mode to FULL. 6. Using the remote control, set the brightness and contrast to normal position. 7. Activate the adjustment mode display of Fig. 1-1 and press the channel button (16) on the remote control to select �TRAPEZIUM�. 8. Press the VOL. UP/DOWN button on the remote control until the both ends vertical lines of the screen become parallel. 2-11: COR TOP/BTM 1. Receive the crosshatch signal from the Pattern Generator. 2. Set the screen mode to FULL. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (17) on the remote control to select �COR. TOP�. 5. Press the VOL. UP/DOWN button on the remote control until the both ends vertical lines become straight. 6. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select �COR. BTM�. 7. Press the VOL. UP/DOWN button on the remote control until the both ends vertical lines of the screen become parallel. 2-12: SEMSOR SAW 1. Receive the crosshatch signal from the Pattern Generator. 2. Press the MENU button. And, then press the LEFT/ RIGHT button on the remote control until the PICTURE menu appears. 3. Press the LEFT/RIGHT button on the remote control to highlight DISPLAY FORMAT. 4. Press the LEFT/RIGHT button on the remote control to select 1080i. 5. Set the screen mode to FULL. 6. Activate the adjustment mode display of Fig. 1-1 and press the channel button (22) on the remote control to select �C.SAW�. 7. Press the VOL. UP/DOWN button on the remote control until the both ends vertical lines of the screen become parallel.
D-3
|
|
|
> |
|