|
Who's Online
There currently are 5819 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
I found this manual to be complete in every detail. Besides the schematic it has a complete set of alignment instructions which are easy to understand. It also includes a complete parts list as well as an explanation of how the power supply and safety shutdown circuits operate. Even a schematic of the tuner is included.
;
The product was good and just what I needed, however I had moderate difficulty with the down load because the sight would not recognize my pass word. I was finally given a direct link to the manual and that worked.
;
Very quick and easy website to use and fast download of manual, quality of manual is excellent and will be pleased to use this service again in the future, thanks so much!
;
It is an very good and clear scanned service manual.
very recommended.
;
Easy to order the manual. Good quality and fast delivery.
ELECTRICAL ADJUSTMENTS
2-12: CENTER PARABOLA 1. Receive the crosshatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (21) on the remote control to select �C.PARA�. 4. Check if the step No. C.PARA is "08". Press the VOL. UP/DOWN button on the remote control until the center of the right and left vertical lines are straight. 2-13: PARABOLA 1. Receive the crosshatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (15) on the remote control to select �EW PARA�. 4. Press the VOL. UP/DOWN button on the remote control until the right and left vertical lines are straight. 2-14: CENTER SAW 1. Receive the crosshatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (22) on the remote control to select �C.SAW�. 4. Check if the step No. C.SAW is "08". 5. Press the VOL. UP/DOWN button on the remote control until the difference of the upper section(A) and the bottom section of the both ends vertical lines becomes minimum. (Refer to Fig. 2-2) A B 00 OSD A 2-19: BRIGHT CENTER 1. Receive the monoscope pattern. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (33) on the remote control to select "BRI CENT". 4. Press the VOL. UP/DOWN button on the remote control until the white 15% is starting to be visible 5. Receive the monoscope pattern. (Audio Video Input) 6. Press the INPUT SELECT button on the remote control to set to the AV mode. Then perform the above adjustments 2~4. 7. Press the DVD button on the remote control to set to the DVD mode. 8. Activate the adjustment mode display of Fig. 1-1 and press the channel button (33) on the remote control to select "BRI CENT". 9. Press the VOL. UP/DOWN button on the remote control D3-3 to set the same step numbers as the AV mode. 07 B Fig. 2-3 2-18: OSD HORIZONTAL 1. Activate the adjustment mode display of Fig. 1-1. 2. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-3) 2-16: TOP CORNER 1. Receive the crosshatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (17) on the remote control to select �COR. TOP�. 4. Press the VOL. UP/DOWN button on the remote control until the upper section of the both ends vertical lines are straight. 2-17: BOTTOM CORNER 1. Receive the crosshatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (18) on the remote control to select �COR. BTM�. 4. Press the VOL. UP/DOWN button on the remote control until the bottom section of the both ends vertical lines are straight.
TV
a 2-15: CORNER
b
Fig. 2-2
1. Receive the crosshatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (20) on the remote control to select �CORNER�. 4. Check if the step No. CORNER is "25". 5. Press the VOL. UP/DOWN button on the remote control until the both ends vertical lines are straight.
|
|
|
> |
|